Vadxx Energy inks deal for first commercial unit

Congratulations to MAGNET incubator tenant Vadxx, who recently signed a MOU with Greenstar Recycling.  Through this joint venture, Greenstar and Vadxx will work together to provide a domestic fuel, and benefit the environment by re-purposing recovered plastic products.

Speaking for Greenstar, CEO Matt Delnick said “Vadxx will help us recover plastics from the material stream and repurpose them as feedstock for the production of oil.  This JV will help us better serve our municipal customers by providing a more consistent market value for their plastics that are otherwise largely unmarketable.  It will increase recovery rates by pulling more plastics out of landfills.”

“Plastics are made from oil, and Vadxx has figured out how to create the lowest sulfur content crude oil in the world, from a commodity that might otherwise occupy space in landfills,” stated Jim Garrett Vadxx CEO. “We are thrilled to partner with Greenstar, one of the top recyclers in the U.S.  The Vadxx equity partnership with its feedstock suppliers is a key component of our business model, which features a low capital investment compared to the expected return from oil sales.”

Greenstar and Vadxx expect that the joint venture will begin producing crude oil in mid-2012 with the target location for the project in Ohio.

Print
Posted by MAGNET Ohio in Entrepreneurship

Most Recent

Top 10 Sited Safety and Health Violations

December 13, 2017 by Gwido Dlugopolsky

One remarkable thing about the list is that it rarely changes.  The order may change but the top cited standards typically don’t change. Top 10 Sited Safety and Health Violations: 501 - Fall Protection 1200 - Hazard Communication 451 - Scaffolding 134 - Respiratory Protection 147 - Lockout/Tagout 178 - Powered Industrial Trucks 1053 - Ladders 305 - Electrical, Wiring Methods 212 - Machine Guarding 303 - Electrical, General Requirements Three of the 10 sited standards are directed at the construction standard (1926) while other fall within the general industry (1910).  It should be noted however that the general industry standard also has fall protection guidelines. Year after year, inspectors see the same on-the-job hazards, any one of which could result in a fatality or severe injury. More than 4,500 workers are killed on the job every year, and approximately 3 million are injured. By understanding these regulations you can improve your safety program and prevent injuries. Give me a call if you have any compliance doubts, or want to review OHSA regulations. Gwido Dlugopolsky at 216-391-7766 or gwido.dlugopolsky@magnetwork.org

Complete ANY Changeover in 10 Minutes or LESS

December 11, 2017 by Gwido Dlugopolsky

Why does it take a NASCAR pit crew only 15 seconds to change four car tires when it takes people like you and me minutes? The answer is simple SMED. Single Minute Exchange of Dies, or SMED, is a process for reducing the time it takes to do equipment changeovers. Using the principles of SMED you should be able to perform any changeover in your facility in under 10 minutes! The SMED process is simple – convert as many changeover steps as possible to “external”, meaning they are done while your equipment is still RUNNING, while simplifying and streamlining the remaining steps. SMED is broken down into the following 3 Steps: Separate Convert Streamline We found this article to be very helping in explaining the SMED process in more detail: LEAN PRODUCTION - SMED           A good first step to achieve this level of SMED efficiency would be to run a kaizen event at your facility to standardize (5S) your tools and supplies. Doing this alone will help you achieve 40% to 50% greater efficiency. Once the “low hanging fruit” is gone, you can still reduce setup times another 20% by practicing more advanced SMED principles.

Coffee is STILL for Closers: 3 Things Needed to Close Any Sale

December 07, 2017 by Sam Wasylyshyn

The secret to closing any sale is to reduce uncertainty in the buyer and replace it with confidence in YOU, your PRODUCT/SERVICE, and your COMPANY. Step 1 – Confidence in YOU Someone buying from you wants to be able to fundamentally connect with you on a human level and feel confident that you’re an expert in what you’re selling If you’re selling paperclips, be an expert in paperclips If you’re selling design and engineering related services, be an expert in design and engineering related services Focus on addressing the problem, not the solution….MEANING you already know you have the solution, connect with the buyer by being an expert with the problem he/she is facing. Prove that you know the problem and all aspects of the problem like the back of your hand. Step 2- Confidence in the PRODUCT/SERVICE you are selling Someone buying from you needs to trust the product/service you are selling will solve their problem. It’s your responsibility to deliver a solution and the benefits associated with it. Basically you need to “Hit a Homerun” communicating this message. Tip – Use Success Stories: Share with the potential buyer examples of your product/service solving problems and delivering value for